|
Product Details:
|
| Keywords: | Battery Management Systems | Base Material: | FR-4 |
|---|---|---|---|
| Surface Finishing: | HASL | Number Of Layers: | 1-2-4-6 Layers |
| Communication: | No | Selling Units: | Single Item |
| Single Package Size : | 13X8X9 Cm | Single Gross Weight: | 0.200 Kg |
| High Light: | 10S 35A Battery Management System,10S 35A Battery Management System Lithium Ion,10S 35A Battery Management Systems |
||
36V BMS 10S 35A Battery Management System Lithium Ion For E Scooter
Li-Ion Battery BMS Description:
How to connect the BMS to the battery pack?
1 Start from the B- wire to the negative of the battery (the B- wire needs to be soldered with a short wire first), then connect the flat cable (the flat cable needs to be removed from the board before connecting the flat cable).
2 Start wiring from B0, connect B0 to the total negative of the battery (this string is not number 1), connect cable B1 next to B0 to the positive of series 1, and connect the third cable B2 to the positive of series 2. The fourth cable B3 is connected to the positive pole of the AA battery ------ and so on.
3 After connecting the cables, measure the voltage between each two adjacent cables from the connector. The voltage of the lithium-ion battery should be less than 4.2V, and the voltage of the lithium-iron phosphate battery should be less than 3.5V.
4 Connect the negative terminal of the charger and the negative terminal of the load to C-. B negative wire and C negative wire need to be welded with thick wire. The wiring method has nothing to do with the color, just the correct order.
5 Then measure whether the total battery voltage is equal to the output voltage of the protection board, if it is equal, it means that the BMS is working normally.
Li-Ion Battery BMS Parameter:
| Model Number | PN-3635D | Surface Finishing | HASL |
| Base Material | FR-4 | Product name | Battery Management Systems |
| Copper Thickness | 1/2OZ 1OZ 2OZ 3OZ | Application | Battery Packs |
| Board Thickness | 1.2mm | Usage | Lithium Battery Packs |
| Min. Hole Size | 0.1mm | MOQ | 1 PCS |
| Min. Line Width | 0.065mm | Number of Layers | 1-2-4-6 Layers |
| Min. Line Spacing | 0.065mm | Communication | no |
FAQ:
Q:1. What current BMS should I choose?
A:Take 10S36V as an example: what current BMS you choose relies on your E-bicycle Motor power and the current limitation of the controller. eg., choose 16A for below 350W, 25A for below 500W, 35A for below 800W, 60A for Below 1000W, higher than 1200W are contact with our service specialist for suggestions, one in all, continue current shall be higher than a current limitation in Controller.
Q:2. Whether my BMS damaged?
A:if you want to judge if the BMS is damaged, please take the following steps, to test if each cell voltage is the same as with the voltmeter. if the cell voltage difference is over 1.0V, the fault is displayed that it cannot run far, no power supply at the start range, short charge time, all these issues are almost caused by battery cells, if BMS damaged is displayed as no charge, no discharge, no discharge while the battery has voltage.
Q:3. Why choose Passional?
1) A professional sales team that provides consultant service and the most competitive battery solutions.
2) Wide-range battery products to satisfy different customers' requirements.
3) Quick response, every inquiry will be replied to within 24 hours.
4) Good after-sale service, long product warranty and continual technique support.
5) With 10 years of experience in manufacturing lithium batteries.
Contact Person: Mrs. Nancy Ouyang
Tel: +86-15889650159
